Thank you for purchasing a High Quality All Balls Racing CVT belt produced by Bando in Japan.  We have partnered with Bando to ensure we are providing the very best CVT belt for your machine.

New belts need to be worn into the mating parts of the CVT transmission.  This will ensure maximum belt life.  While the belt is being worn into the mating parts, it is critical to follow the basic steps outlined below.  It is also important to understand why the previous belt failed.  If components are worn in the system, maximum belt life will not be achieved.  Before installing a new belt, inspect CVT primary and secondary clutch for damage or wear and fix or replace necessary components.  Thoroughly clean CVT belt sheaves with a Scotch-Brite™ pad and warm soapy water removing any rubber material, residue, or oil.  Make sure all surfaces are dry before running the belt.  Install the belt using installation tools designed for your machine, following the factory recommended procedure.  The orientation of the belt is not important, but it is recommended that the All Balls Racing logo is readable after the belt is installed on the vehicle.  This will ensure that if the belt is ever removed, it is reinstalled in the same orientation. 

For the first 10 miles, use low range and avoid high loads and speeds while varying speeds continuously. 

For the next 50 miles avoid full throttle and vary speeds continuously. 

Use low range when necessary, during the entire lifetime of the belt to avoid hour glassing damage caused by slipping.

Inspect and service CVT system regularly to maximize belt life.

If belt housing becomes wet, stop and drain water immediately.  Avoid high loads and speeds until the housing expels all water and dries out.  Service the CVT system as soon as possible to avoid damage.

LENGTH OF WARRANTY 

All Balls Racing warrants its CVT Belts against defects in material and workmanship, under normal use and service, for a period of two years from the date of purchase. This warranty is valid for a one-time redemption per purchase. All Balls Racing’s obligation under this warranty is limited to repairing or furnishing a similar product without charge. All Balls Racing shall have the option of requiring the return of the defective material, upon request, to establish the claim. All claims must be made through the completion of all fields on this site. No allowances will be made for repairs or alterations without All Balls Racing’s written consent or approval. All Balls Racing shall not in any event be liable for any special indirect or consequential damage. THERE IS NO IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. 

GENERAL DISCLAIMER 

All Balls Racing Group products are intended for closed-course racing only and are not for aircraft use. All Balls Racing Group warrants solely to the original retail customer that its products are free from defects in design, materials, and/or workmanship for 1 year from the original date of purchase, unless otherwise stated. All Balls Racing Group products are sold “as-is” without warranty, express or implied, including any warranty of merchantability of fitness for a particular purpose. All Balls Racing Group and their parent company Arrowhead Engineered Product shall assume no liability or responsibility whatsoever for any damages or expenses caused by or relating to the failure of any All Balls Racing Group product. Neither manufacturer, nor distributor, nor dealer shall be liable for any indirect, consequential, incidental or punitive damages sustained by purchaser or any other person arising from or related to the use of any All Balls Racing Group product. All Balls Racing Group and Arrowhead Engineered Products shall not be liable and will not reimburse for labor charges or incidental and/or consequential damages. Purchaser acknowledges that they have the expertise as to the intended use of the All Balls Racing Group product, and therefore assumes all risk and liability resulting from installation and use of the All Balls Racing Group product, whether used singly or in combination with other products. Any dispute arising out of or related to the use of an All Balls Racing Group product must be settled in Anoka County, Minnesota, and shall be governed by Minnesota law. Purchaser and any other person using this product consent to the jurisdiction of the courts of the State of Minnesota for resolution of any disputes. Purchaser agrees the use of the All Balls Racing Group product constitutes acceptance of these terms. 

All Balls Racing Group reserves the right to make the determination if the part has been subject to normal wear, misuse, abuse, negligence, accident, improper installation or alteration, and all such determination shall be final. All Balls Racing Group shall not extend any warranty or guarantee to products that have been sold by private parties or other unauthorized resellers of our products. 

WARRANTY CLAIMS 

To initiate a warranty claim, fill out the fields below, carefully following the instructions. All fields and actions must be completed within 30 days of part failure including sending the part in upon request. Please contact us with questions.